Aluminium is kind of white solid, insoluble in water, no smell and tasteless. The quality is extremely hard. It is easy to absorb moisture but not to get rid of it. Amphoteric oxides is soluble in inorganic acid and alkaline solutions, almost insoluble in water or non polar organic solvents. Relative density (d204) is 4.0. Its melting point is about 2000 ℃.
The pressure spray dryer integrates drying and granulating functions. According to the technological requirements of adjusting pressure, flow rate and size of atomizing hole, a certain size and proportion of spherical particles can be obtained. Spray the raw material of liquid or paste into tiny droplets, extract it from the pressure of the isolation pump by pressure spray, and dry quickly through adequate heat transfer (10 ~ 90 seconds). At the end, a powder or small particle is obtained.
The liquid or paste raw material is sprayed into small liquid drops by pressed sprayer draw assistance from pressure of diaphram pump, and quickly drying through amply heat exchange (10-90sec.). Most of the powder granules are collected from outlet of discharge at the bottom of the spray dryer. The wasted air and fine powder are separated by the cyclone. The wasted air is exhausted from draft fan, while the fine powder is collected at the bottom of cyclone. There is a second grade duster equipped at the outlet. Therefore, the recovery rate of the finished powder granule can reach 96% to 98%.
● Wide application scope. According to the characteristics of raw material, it can use hot air to dry and use cool air to granulate. It has strong adaptability to each kind of raw material.
● Simple and stable operation, convenient control, easy realization of automatic operation.
● Special granulating nozzle has been produced for moiten property granulating tower, and can granule 0.5-3mm grains such as stearic acid agent, rubber additive, olein, etc.
This machine uses the pressure atomizer to disperse the material into fog, fully contact with the hot air to complete instant drying, and forming powder products. The air passes through the initial, medium, high efficiency filter and then enters the top air distributor from the heater. The hot air enters the drying chamber in a spiral and even way, and can be dried into finished product in a very short time in contact with the hot air. The finished products are continuously captured by tower, cyclone separator, water dust collector, and exhaust gas is discharged by induced fan.
● Ceramics: Aluminium Oxide, Ceramic Tile Material, MagnesiumOxide, Talcum, etc.
● Others: Calmogastrin, Hime Chloride , Stearic Acid Agent, etc.
● Regarding major electrical components , there are international brands for selection such as ABB , Siemens or Schneider, etc.
● Regarding raw material of machine, there are choices such as AISISUS304 , AISISUS304L, AISISUS316,AISISUS316L, carbon steel, etc.
● Regarding control system, there are push button, PLC+HMI, etc for choose.
● According to customers’ specific requirements, the explosion-proof system can be designed.
● The fitting system of spray dryer including pneumatic conveying system, etc. can be supplied.
● The heating system of spray dryer is very flexible, which can be configured based on the customer site conditions such as steam, electricity, gas furnace and so on. The spray dryer supplied by VAPORUN can be designed to match these conditions.
● Without heating system, it can be a cooler to make particle with cooling air.
The pressure measuring device in the main tower of spray dryer can observe the operation state according to the negative pressure. Cyclone has a pressure difference device. According to the pressure difference it can be judged whether there is cyclone blockage phenomenon. Likewise, according to the main tower air filter pressure difference transmitter, it can be judged whether there is blockage filter. With the increase of drying tower straight section, the material stay time can be prolonged, so as to improve production capacity.
Griffin Technology Manufacturing Co., Ltd.
Griffin technology manufacturing Co,. Ltd, a factory with more than ten years experience of professional and technical industrial service. locates in Changzhou city of Jiangsu. Our company has 2 large modern construction machinery manufacturing plant, equipped with whole line of sheet metal bending, laser cutting, automatic polishing, automatic welding, occupies an area of 500,000 square meters. Also we have our own R&D team, which has a number of talents and individual test lab. We are specializing in researching and developing drying machine, such as spray dryer, mesh belt dryer, fluid bed dryer, flash dryer, air stream dryer, vacuum dryer, plate dryer and so on. As auxiliary machines of drying machine, we also supply mixer, granulator, grinder and screener, roller compactor, air flow mixing system and air flow conveyor. With rich experience, we keep leading in design and manufacturing Chinese herbal extract spray dryer, flavouring spray dryer, hydrolyzed protein spray dryer, desiccated coconut drying machine, coconut meat mesh belt dryer, pharmaceutical spray dryer, vegetable and fruit dehydrator (mesh belt dryer), bread crumb fluid bed dryer, enzyme spray dryer, chicken powder production line, seaweeds drying processing line, gelatin production, WDG production line and so on. Based on keeping stable quality of drying, mixing, granulating, crushing and sieving machines, we actively research and develop new product, like roller compactor, airflow conveying and mixing system, vacuum belt dryer, try to supply turnkey projects to our customers. After years of research and production experience, we have absorbed a wide range of latest technology in drying technologies. We always insist on win-win cooperation, and we are deeply trust in "One for all, all for one! "
- Company Name: Griffin Technology Manufacturing Co., Ltd.
- Representative: wanxingwei
- Product/Service: Spray Dryer , Fluid Bed , Belt Dryer , Vacuum Dryer , Pharmaceutical equiment , Chemical equiment
- Capital (Million US $): 1170,000RMB
- Year Established: 2021
- Total Annual Sales Volume (Million US $): US$10 Million - US$50 Million
- Export Percentage: 81% - 90%
- Total Annual Purchase Volume (Million US $): US$5 Million - US$10 Million
- No. of Production Lines: Above 20
- No. of R&D Staff: 21 -30 People
- No. of QC Staff: 51 -60 People
- OEM Services Provided: yes
- Factory Size (Sq.meters): 5,000-10,000 square meters
- Factory Location: Xinbo Zhihui Valley, 198 Yunhe Road，Changzhou，China
- Contact Person: Mr. frank
- Tel: 86-17605290094
Premium Related Products